Condux Mini-Blower/Pusher Instrukcja Użytkownika

Mini-Blower/PusherUSER'S GUIDE & SAFETY MANUALCONDUX

103. Adjust down pressure on cable by tightening the spring tensioned down pressure adjustment to ensure positive contact with drive roller. (See f

2. Open air control valve to engage air pressure. (See figure 14)Important: Optimum air pressure not to exceed 40 PSI in microduct.3. Engage drive sys

124CABLE PACK VENTURI CABLE SEALPack Cable OD P/N Cable OD P/N Cable OD P/N10.23-0.34 (5.8-8.8)08780802 Pack #10.23-0.34 (5.8-8.8)087808030.23-0.28 (5

1323PACKCABLE PACK VENTURI CABLE SEAL CABLE GRIPCable OD P/N Cable OD P/N Cable OD P/N Cable OD P/N10.23-0.34 (5.8-8.8)08780393 Pack #10.23-0.34 (5.8-

14B.Duct Rod PusherAPPENDIX

15DUCT ROD PUSHER (08081301)ITEM PART NUMBER DESCRIPTION QTY1 02021400 CAPSCREW, HEX HEAD 1/4-20 X 0.75LG GR5 CZ 22 02102001 FLATWASHER, 1/4 TYPE A NA

16BLOWER/PUSHER ASSEMBLY (08780800)ITEM PART NUMBER DESCRIPTION QTY1 02288338 CAPSCREW, #10-24 x 1.50LG COUNTERSUNK 22 08081301 DUCTROD PUSHER ASSEMBL

17MINI-BLOWER ASSEMBLY (08081315)ITEM PART NUMBER DESCRIPTION QTY1 00263400 CORD,QUAD-RING 3.5MM CS X 3.75LG 22 02020000 FITTING,HYD 1/2IN MALE NIPPLE

18CLAMP ADJUSTMENT SCREWITEM PART NUMBER DESCRIPTION QTY1 02102001 FLATWASHER, 1/4 TYPE A NARROW CZ 12 02287600 FLATWASHER, 1/4 NYLON 23 02288555 CAP

19MOUNT CLAMP ASSYITEM PART NUMBER DESCRIPTION QTY1 02102001 FLATWASHER, 1/4 TYPE A NARROW CZ 12 02290268 SCREW,SHOULDER 1/4 DIA X 3.25LG 13 08081311

2Read and understand all procedures and safety instructions before using the Mini-Blower/Pusher. Observe all safety information on this page and note

© Copyright 2011, Condux International, Inc. Printed in USA Literature Part Number: 08780899 Revision Number: 1.1Condux International, Inc. P.O. Box

3Table of Contents12567General Information ... 4Technical Specifications ...

41.General InformationThe operating instructions contain a full description of the Condux Mini-Blower/Pusher, which has been designed for the purpose

5OPERATOR QUALIFICATIONSa. Operator must know the required safety directives to run the machine that arepertinent to the country where it is being use

63.Safe Operating PracticesRead and understand all procedures and safety instructions before using the Condux Mini-Blower/Pusher. Observe all safety

7Actual parts:08081315 – blower assy08081301 – pusher assy08764110 – 12 mm duct pack08764150 – 12.7 mm duct pack08780302 – .23-.34 cable pack08780304

82. Once in place, secure the Blower Assembly to Drive Assembly using(2) #10-24 x 1 1/2" Capscrews. (See figure 3)3. Select and install the appro

96. Load cable through drive assembly. Select and install the appropriate size cableseals for the specific project. (See figure 7)7. Install top ven